Copyright 2017 - Custom text here

Автопилоты

OSD package includes:
(1) Skylark Tiny OSD
(1) Skylark 10Hz GPS
(1) 60A Current sensor
(1) 200mm male to male servo wires

(1) USB Update Cable

 

Feature:
- Build in barometer.
- The smallest OSD in the world.
-  Build in 60A Current sensor.
-  Online firmware upgrade.
-  Selectable OSD Screen.
- XT60 connector
-  Fly summarize
-  High  precision current sensor
- 10Hz super sense GPS, with backup battery ,3D Fix led indicator.
-  PAL/NTSC compatible
-  ultra-light : 22.5 gram
- RSSI Auto detected.
- Auto "Setting Home"
-  With barometer

OSD measures: 
Speed | Altitude | Distance                                                    
Home navigation angle
GPS signal
Power battery voltage
Power battery current
mAh consumed                                                                             

 

Lastest Version Skylark Tiny OSD III (built-in Barometer) T-plug Connector

Price:
$109.61
Weight:
0.40 KG
 

Skylark Rock OSD for 12S battery(50V voltage/180 A current)

  • Price:$142.49  Weight:0.20 KG
 

Features:

contactless Current Sensor
Support 3S-12S battery
With 5V/12V selector switch for VTX and camera
Including barometer
180A current sensor
Skylark 10Hz GPS
Support Skylark Auto Antenna Tracker
Free firmware upgrade
Weight: 30g (w/ XT60 connector)

 
 

Features:

contactless Current Sensor
Support 3S-12S battery
With 5V/12V selector switch for VTX and camera
Including barometer
180A current sensor
Skylark 10Hz GPS
Support Skylark Auto Antenna Tracker
Free firmware upgrade
Weight: 30g (w/ XT60 connector)       

 

[GPS/INS OSD] Skylark Dianmu OSD with RTH

Price:
$183.33

 

All In One Pro Flight Controller V2

 
 
Your Price:

£49.95http://www.unmannedtechshop.co.uk/all-in-one-pro-flight-controller-v2/

 

 

Using Xbee radios for telemetry with APM

500 x 500 | 55.9KB | copter.ardupilot.com
 

Product Description

This is the updated V2 All in one Pro Flight controller board with a reinforced USB connector

The Crius All in one Pro Flight controller is a multi rotor flight controller that is compatible with both the MultiWii and the MegaPirate open source autopilot software.  This board includes everything you need for your flight controller using the next generation sensors like the MPU6050 with a 3 axis compass, and the MS5611 high precision altimeter (can measure about 10cm in height change).  Another nice feature is that an FTDI interface is built in so you can program and configure this board via a micro USB cable.  This All in One Pro flight controller also has a dedicated i2C port for GPS so you dont need an external GPS interface board.  There is an addon GPS module for this board based on the LEA-6H module.

You can also use this board with the Arducopter and Arduplane code with some minor changes.  Please see the links below for more information

This is definitely one of the most cost effective flight controllers you can get without compromising on sensor quality.

All In One Pro Specifications

  • Supported MegaPirateNG (arducopter) and MultiWii firmware
  • Up to 8-axis motor output
  • 8 input channels for standard receiver
  • 4 serial ports for debug/Bluetooth Module/OSD/GPS/telemetry
  • 2 servos output for PITCH and ROLL gimbal system
  • 1 servo output to trigger a camera button
  • 6 Analog output for extend device
  • A I2C port for extend sensor or device
  • Separate 3.3V and 5V LDO voltage regulator
  • ATMega 2560 Microcontroller
  • MPU6050 6 axis gyro/accel with Motion Processing Unit
  • HMC5883L 3-axis digital magnetometer
  • MS5611-01BA01 highprecision altimeter
  • FT232RQ USB-UART chip and Micro USB receptacle
  • On board logic level converter
  • Dimension: 50mmX50mm
  • Height: 11.6mm
  • Weight: 14.2g
  • hole spacing: 45mm
  • Hole diameter: 3mm

Package Contents

  • AIO PRO flight controller module x 1
  • 3Pin to 1Pinx3 cable 100mm x 3
  • 3Pin to 3Pin cable 100mm x 1
  • Molex 1.25mm 4Pin cable 100mm x1
  • Molex 1.25mm 6Pin cable 100mm x1
  • Molex 1.25mm 8Pin cable 100mm x2

AIO Pro Resources